Page Contents
What Does F2 Mean On A Stove
F2 on a stove means that the stove oven has exceeded the maximum threshold for temperature due to unknown reasons. F2 is usually a code that indicates that the temperature of the oven has become more than 300 degrees Fahrenheit. F2 usually arises during baking which means that the oven temperature is at fault.
The F2 codes in G.E. Stoves indicate the Stoves furnace exceeded its temperature limit threshold due to an unknown cause. F2 codes are errors in the range and components, not in the interior of the stove.
If an F2 code appears on your G.E. Stove while it is being cleaned, that means either the temperature sensor in the stove or the door latch is the problem. F2 codes on G.E stove may occur while baking, which means either the oven has actually been overheated, or that the oven temperature sensor is at fault.
| F2 | Features |
| F2 Codes | The F2 codes in G.E. Stoves indicate the Stoves furnace exceeded its temperature limit threshold due to an unknown cause |
| F2 Error Code | F2 codes are errors in the range and components, not in the interior of the stove. |
When an F2 code is displayed, an F2 error code means the oven temperature has exceeded its maximum setting. If your GE oven displays an F2 error code (or an F20), that means that it has detected an internal temperature rise beyond the preset threshold. If you have a GE oven, an F2 error code on your oven means the temperature sensor has detected temperature exceeding the predetermined threshold.
If you see F2 on cold, this could mean that your ovens electronic control board is malfunctioning, or that your ovens temperature sensor is malfunctioning. If your oven is measuring this type of temperature, the problem could be caused by malfunctioning sensors or damaged control boards. If sensor probes are not working, in addition to an F2 code, the oven may shutdown too early.
If you’re interested in Can Bacon Grease Go Bad then you can check that article.
Contact the installer or electrician to fix a bad electrical connection, and the appliance should work properly. If you reboot your stove and the problem is still there, you will have to call a repair service to get assistance. If the displayChild Lock does not disappear, and you cannot get back control of the oven, you will need to contact a repair service.
To reset your oven, disconnect and leave unplugged for at least 30 seconds. If the self-cleaning cycle has not completed, use the following instructions to clean your oven. If you attempt to BAKE or ROIL food in your oven soon after the cool-down time for the self-clean cycle has ended, the oven displays OFF.
F2 is a code indicating the oven was turned off during the self-clean cycle. F2 indicates that the oven was turned on when the self-clean feature of the oven was active.
You can test whether this is the case by disconnecting the oven, allowing it to sit for 10 minutes, then turning it back on. This can be frustrating if you cannot shut off your oven, so you may need to unplug it in certain situations. Turning off typically happens if you forget to turn the oven off after cleaning. To test whether it is turned on, turn off the oven, wait 30 seconds, and open the oven door.
If you’re interested in Will A Gas Stove Work Without Electricity then you can check that article.
If oven light stays lit, even when oven door is closed, this may be an indication of heating element issue. The display can also be caused by loose wires or by malfunctions with door locking mechanisms, which are common with self-cleaning ovens. A show can mean a Kenmore Oven is having trouble with regulating temperatures, usually due to the control board or faulty sensors.
A Hot Point oven may display an F2 error code when a sensor is not working, the cords or heating elements are damaged, or if the control board is defective. A HotPoint Oven will display an F2 error code when the ovens interior temperature is above 590 degrees F when you open the doors. F2 Error Codes on Hotpoint Ranges A Hotpoint Range indicates that the oven temperature exceeded 590 degrees with the door unlocked. A Kenmore Oven displays an F2 error code when the ovens temperature measured from its sensors is too hot.
The F2 error may occur when baking, or while the General Electric oven is in the Clean setting.A When this error code does occur, the oven is inoperable until the problem with the oven is resolved.
If, after you have reset the General Electric oven, the F2 error code is still appearing, then you need to identify what the faulty component is, since, as stated earlier, an F2 error means a component needs replacing, but first you have to figure out what the component is. If your LG oven error code reappears, that means the relay board in your oven needs to be repaired or replaced. The F1 error means there is an electrical fault inside of the oven. The error may also mean data corruption in the electronic control of the oven.
Error codes, or fault codes, are programmed into all General Electric oven controls. Fault codes help General Electric appliance factory service technicians diagnose problems quickly on your range or wall oven.
Sometimes, turning off the circuit breaker the range or wall oven is connected to will reset an error, fault, or function code in the range or wall oven within 30 seconds. It is OK to leave the breaker on and power on the range again just long enough for you to use the surface units. There are cases when oven controls will not reset, and you might need a repair.
Most ovens are programmed to shutdown when they get a specific temperature beyond the considered safe limits. Convection ovens sometimes also include a temperature probe which will make the oven emit a chime when it is 75% through its initial cook time. If the overrun happens when using a GE oven, immediately shut down and disconnect from power, either by unplugging it or turning the circuit breaker off.
If you notice any odd sounds coming from your oven, immediately turn the power off and call a repair professional. If a sensor fails, the control panel sends a signal to the burners that flames are down.
Resetting it should eliminate the error, fault, or feature, and if it does not fix your gas cooker problem, then you might have to call in the professionals to perform a repair. If any of the wiring is exposed or damaged, the temperature sensor in your General Electric oven is reading the temperature incorrectly, which is what causes an error code of F2.
How do I fix the F2 code on my Whirlpool stove?
To erase the error code and see the F2 code, press and hold any key. Choose “cancel” and wait a minute to check for mistakes. Disconnect the power and replace the control if the problem persists. Within 60 seconds of the appliance being powered up, the error code F6-E0, Return Line Not Connected, should show.
How do I get my stove to stop beeping?
Electronic appliances occasionally need to be restarted, just like a computer. Unplug your oven from the power source and keep it there for at least 30 seconds to reset it. It will be important to identify the source of the problem code if the beeping returns once the oven is reconnected.
What does F2 mean on a glass top stove?
The F2 error number in this situation denotes an excessively high oven temperature. However, this does not necessarily imply that the oven’s internal temperature is too high. The resistance of the sensor circuit is measured by the oven control board (clock).