Skip to Content

How To Reset The Maytag Dishwasher Control Panel

How To Reset The Maytag Dishwasher Control Panel

How To Reset The Maytag Dishwasher Control Panel

To reset the Maytag dishwasher control panel, simply unplug the dishwasher for about 15 minutes. After 15 minutes, turn on the dishwasher again and press any three buttons consecutively. Repeat the steps one more time, and you’re done.

You can reset your control lock by pressing either Start/Resume, the Cancel button, or pressing Lock for 4 seconds. You can reset the Maytag dishwasher error codes by unplugging the Maytag dishwasher for at least 60 seconds or disconnecting the circuit that supplies the dishwasher with power.

You can reset your Maytag dishwasher flashing lights by first opening and closing the doors. To reset your Maytag 200 (quiet-series) dishwasher control panel, unplug the power for one minute and plug the appliance back in.

By the way, if you’re interested in Does Brown Sugar Go Bad, check out my article on that.

How do I reset my dishwasher control board?

Depending on the make and type of your dishwasher, there are many ways to reset the control board. Here is a basic procedure you might use:

  • Disconnect the Dishwasher’s Plug: To avoid electrical mishaps, ensure the dishwasher is unplugged from the power source.
  • Wait: Unplug the dishwasher for some time, typically between 5 and 10 minutes. The control board may occasionally be reset due to the internal capacitors being able to discharge.
  • Plug it Back: Reconnect the dishwasher to the power source by plugging it back in.
  • Factory Reset (if applicable): A precise button combination must be pressed to factory reset some dishwashers. To learn how to do this, consult the user handbook for your dishwasher. Normally, pressing and holding a particular set of buttons on the control panel would be required.
  • Control Lock/Unlock: Control boards can occasionally be locked to stop unintentional changes. Look for a “Control Lock” button or indicator on the control panel. If this function is enabled on your dishwasher, you may unlock the controls by pressing and holding the “Control Lock” button briefly.
  • Circuit Breaker Reset: Resetting the dishwasher’s circuit breaker in your home’s electrical panel is another option if the previous methods don’t solve the problem. After turning it off for a while, switch it back on.

Remember that the particular processes may vary depending on the make and type of your dishwasher. For the most precise and suitable reset procedures, always consult the user handbook for your dishwasher.

It is preferable to call a qualified technician for assistance or speak with the manufacturer’s customer service if you are unclear or uncomfortable doing these steps.

How to reset the Maytag dishwasher control panelBenefits
Unplug the dishwasher for about 15 minutesTo get rid of germs
After 15 minutes, turn on the dishwasher again and press any three buttons consecutivelyIt takes limited space
It saves water and energyIt saves water and your energy
How to reset the Maytag dishwasher control panel and its benefits.

How do I unlock my Maytag dishwasher control panel?

Maytag dishwasher models may vary, but generally, here’s how you can unlock the control panel:

  1. Locate the Control Lock Button: Look for a button labeled “Control Lock” or with a similar icon on your Maytag dishwasher’s control panel. The icon may look like a padlock or a key symbol.
  2. Press and Hold the Control Lock Button: Hold the “Control Lock” button for 3 to 5 seconds. You should see an indicator light turn off or change on the control panel, indicating that the control lock has been deactivated.
  3. Test the Controls: After releasing the “Control Lock” button, try pressing other buttons on the control panel to ensure they respond as expected. If the control lock was the issue, your dishwasher controls should be functional again.

If your Maytag dishwasher doesn’t have a dedicated “Control Lock” button or if this process doesn’t work for your specific model, I recommend checking your dishwasher’s user manual for detailed instructions on how to unlock the control panel. If you no longer have the manual, you can often find manuals online on the Maytag website or through various appliance manual databases.

If you’re still unable to unlock the control panel despite following the manufacturer’s instructions, it might be best to contact Maytag customer support or a professional appliance technician for assistance. They can provide you with specific guidance based on your dishwasher model and its features.

Find out how to reset the Maytag dishwasher control panel

What causes the dishwasher control panel to stop working?

There are several potential reasons why a dishwasher control panel might stop working. Some of the common causes include:

  1. Electrical Issues: Faulty wiring, a blown fuse, or a tripped circuit breaker can disrupt power to the control panel, causing it to stop working.
  2. Control Lock: Many dishwashers have a control lock feature that prevents accidental changes to settings. If this feature is enabled, the control panel might appear unresponsive.
  3. Water Damage: Moisture or infiltration into the control panel area can lead to malfunctions.
  4. Control Board Malfunction: The control board, also known as the control module or electronic control board, is the “brain” of the dishwasher. If it fails or becomes damaged, the control panel may stop responding.
  5. Faulty Buttons or Membrane: The individual buttons on the control panel might fail due to wear and tear, making it seem like the whole panel is unresponsive.
  6. Software Glitch: Like any electronic device, dishwashers can experience software glitches that cause temporary issues with the control panel.
  7. Sensor Issues: Modern dishwashers often have sensors that detect water levels, temperature, and other factors. If these sensors malfunction, they could affect the control panel’s behavior.
  8. Wiring and Connections: Loose or damaged wiring connections between the control panel and other components can lead to communication problems.
  9. Door Switch Problems: Dishwashers typically have door switches that prevent operation when the door is open. If the door switch malfunctions, it might prevent the control panel from working.
  10. Power Surge: A power surge or electrical spike can damage the sensitive electronics in the control panel.
  11. Component Failure: Other components within the dishwasher, such as the touchpad, display, or user interface, could fail and impact the control panel’s functionality.
  12. Age and Wear: Electronic components can degrade over time due to age and regular use.

If your dishwasher’s control panel stops working, here are some troubleshooting steps you can take:

  1. Check for a “Control Lock” feature and try unlocking it.
  2. Verify that the dishwasher receives power by checking the circuit breaker and outlet.
  3. Look for any visible signs of water damage or loose wiring.
  4. Try a power cycle by unplugging the dishwasher for a few minutes and then plugging it back in.
  5. Consult the user manual for specific troubleshooting steps for your dishwasher model.
  6. If none of these steps work, contact the manufacturer’s customer support or a professional appliance technician.

To learn about Does Sugar Go Bad, check out my article where I cover everything you need to know.

Dishwasher Issues: Troubleshooting, Repair, and Replacement Considerations

If you are experiencing problems with your dishwasher, you will want to find out what is causing the issue and whether or not you need to have the dishwasher repaired or replaced.

If the above troubleshooting tips have not solved the issue and your dishwasher is still failing, then the best thing to do is to get a certified professional to solve the issue. After hiring a professional to evaluate your dishwasher, the pro will determine whether you need repairs or replacement.

In the event that you are replacing the dishwasher, it is recommended that you hire a professional that will remove your old dishwasher and set up your new dishwasher.

Suppose the key on the control panel is stuck, or your dishwasher control panel issue cannot be fixed by resetting your dishwasher control panel, removing a child safety lock, or turning the electricity on.

In that case, your dishwasher control panel repair may actually be a replacement. If those functions are not engaged and your dishwasher does not respond when you press the buttons, your control panel might be soaked or damaged.

Maytag Dishwasher Installation Precautions and Power Management

Just keep in mind that if your Maytag dishwasher does not have an outlet, you will have to shut down the unit on the breaker (again, one minute). Turn the power off or unplug the dishwasher (you could go the Circuit Breaker route as well).

Reconnect power Control operation# Read your dishwasher’s user manual, which comes with the lowest-wattage, lowest-energy-use motor on your dishwasher. Cabinet opening — existing utilities Electric shock hazards Before installing the dishwasher, disconnect power to your power supply from your fusebox or circuit breaker box.

What may have caused the malfunction in my Maytag dishwasher?

If your dishwasher is still behaving unresponsively, it may be time to restart it. To reset your dishwasher, you need only pull the plug and let it sit for a full minute before plugging it back in. If the dishwasher does not have a plug, turning off the circuit breaker may be of assistance.

What could be causing the electricity to be cut off to my Maytag dishwasher?

If the dishwasher is hard wired to the power source, turn off the breaker at the house’s electrical panel for one minute, and then turn it back on. If the dishwasher is not hard-wired to the power source, skip this step. If your dishwasher does not have any electricity, lights, or other features, please check to see whether the Control Lock has been activated.

What would you say is the most typical issue that arises with a Whirlpool dishwasher?

One of the most frequent problems is a broken input valve. Suppose the input valve does not accurately regulate the amount of clean water allowed into the machine.

In that case, you may experience various problems (one of which is that the dishwasher will not fill with water). If the problem can be traced back to the input valve, you will most likely be required to have it repaired.

Skip to content